(n.) A metal or metallic alloy used when melted for uniting adjacent metallic edges or surfaces; a metallic cement.
(n.) anything which unites or cements.
(n.) To unite (metallic surfaces or edges) by the intervention of a more fusible metal or metallic alloy applied when melted; to join by means of metallic cement.
(n.) To mend; to patch up.
Example Sentences:
(1) This study compared soldering by a conventional torch procedure with an infrared soldering technique.
(2) However, the effect of the soldering atmosphere on the tensile strength was small.
(3) No effects on behavioral function were observed among the solderers.
(4) This contaminant was not present after a control exposure while soldering on iron.
(5) The following therapeutic proposal was adapted: On the maxilla, a three-step procedure: first step: building of metal copings on 13, 16 and 26 and metal-ceramic crowns on 11 and 21, second step: building of telescop crowns on 16 and 26 and clasps on 13, 11 and 21, third step: casting of the removable partial denture framework and soldering to the telescop crowns and clasps.
(6) Wettability of the liquid solder on UNI METAL was better than on Victory II.
(7) The stainless steel shank is a cathodic component of a three-way galvanic cell, whereas the silver soldered joint is an anodic component.
(8) If you only have an 20cm tin you can use that instead, but don't use all the batter – about 80% will suffice – otherwise you'll end up with a volcanic overspill, cake soldered to the floor of the oven and a frayed temper.
(9) Using the rat as a model, a partial transection of the ventral urethra was repaired in one of three ways in 39 animals: conventional microsuture repair, laser assisted microsuture repair and laser assisted microsuture repair with a protein solder.
(10) Three alloys had corrosion resistance superior to the other solders.
(11) We form a kind of chain, soldered together by grief and suffering, but also by a way of living and thinking which the killers wanted to destroy.
(12) Workers in the following job categories experienced the highest annual mean PbB levels: paste machine operators (battery plants), solder-grinders (assembly plants), and crane operators (foundries).
(13) Soldering flux used in the electronics industry can cause both irritant and allergic contact dermatitis.
(14) Soldering fractures constitute an important cause of the removal of appliances during the first 8 years following application.
(15) In this study about melting and torchs employed in solder in fixed prosthodontics, it's analysed the accurate melting, adequate quantity, as well as protection of adjacent tissues with an accurate anti-melting.
(16) Two cobalt-chromium alloys (Blue Elgiloy, Crozat) and an austenitic stainless steel alloy (Remanium) were soldered by an electrochemically generated hydrogen-oxygen flame forming an overlapped joint design.
(17) The aim of this study was to determine the release of Au, Cu, Sn, Zn, and Ag from five commercially available Cd-free gold solders.
(18) The question of whether to cast in one piece or in multiple sections that are soldered is discussed.
(19) In the case of soldering electrically wrought wire clasps to metal structures such as rests and connectors, there is no fear of of overheating a wide area of wires.
(20) In the sample studied the proportion of foods contained in non-soldered as opposed to soldered cans has risen consistently during the survey and now accounts for 83% of all samples (excluding sardines).
Welding
Definition:
(p. pr. & vb. n.) of Weld
Example Sentences:
(1) Tests were undertaken to study resistance to tears in laser welded dental metal alloys.
(2) The possibility of contaminating the breathing air zone with hazardous substances in manual and semi-automated welding increases with the intensity of their formation in the arc zone.
(3) Laser repair has not been widely accepted both because the effect of laser irradiation on intact nerves is not well documented, and the anastomotic strength of the weld has been inferior to suture repair.
(4) The highest combined exposure (10-fold allowable value) was that of welders of steel coated with the zinc layer, using the metal active gas welding.
(5) The concentrations of 17 trace elements (e.g., copper, cobalt, iron, manganese, chromium, silicon and magnesium) were determined in whole blood samples of 81 persons working with different welding methods on stainless steel or aluminium and 68 nonwelders.
(6) These figures represent a participation rate of 37.1% in welders and 36.7% in non-welding subjects.
(7) Weak welds occurred with no thermal damage obtained at lower irradiances: stronger welds with thermal damage confined to the weld site occurred at higher irradiances.
(8) The results support the hypothesis that mild steel welding and to a lesser extent stainless steel welding with tungsten inert gas is associated with reduced semen quality at exposure in the range of the Danish process specific threshold limit values of welding.
(9) Low-level exposure to hexavalent chromium associated with TIG stainless steel and mild steel welding do not appear to be a major hazard for human spermatogenesis.
(10) Whereas the patterns of lung cancer mortality in these results suggest that the risk of lung cancer is higher for stainless steel than mild steel welders the different level of risk for these two categories of welding exposure cannot be quantified with precision.
(11) The occurrence of reduced birthweight, preterm delivery, infant mortality, and congenital malformation was not increased among children at risk from paternal welding exposure in comparison with children not at risk.
(12) The goal of future research should be to make the procedure less operator-dependent (dye enhanced or automated welding).
(13) When nacreous shell produced by the marine oyster Pinctada maxima, used as a biomaterial in oral surgery, is implanted in human bone, new bone formation occurs, resulting in a tight welding of the bone to the nacre [16].
(14) Tensile strength, 0.2% proof stress, and percentage elongation of the welded bars were measured and compared with the corresponding values for the titanium bars as delivered and with those of brazed type-3 gold alloy bars of similar dimensions.
(15) It was proved in experiment that endothelium formation is more adequate in a vascular microsuture formed by laser welding than in the formed by the traditional thread method.
(16) 23.2% of patients with pneumoconiosis caused by electric-welding aerosol showed regress of pneumoconiosis in afterdust period.
(17) Results indicated that excellent welds can be obtained with very little loss of strength and ductility in the area of the weld joint.
(18) Dizziness, headaches, and weakness occurred among three men after short-term hydrocarbon exposure during improper welding procedures in a closed container.
(19) In periods of reconstruction of chemical enterprises, hazardous compounds concentrations may exceed MAC, they are also characterized by contamination of the skin with toxic substances, welding aerosols discharge into the working zone, and microclimate distabilization.
(20) A limited investigation was carried out of the use of glass and ceramic fibre products used as protection against welding 'batter' and oxyacetylene welding flame.